ASTM C29/C29M

ASTM C29/C29M

Standard Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate
Standard Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate
Standard Test Method for Bulk Density ("Unit Weight") and Voids in Aggregate
Standard Test Method for Bulk Density ("Unit Weight") and Voids in Aggregate
Standard Test Method for Bulk Density ("Unit Weight") and Voids in Aggregate
Standard Test Method for Unit Weight and Voids in Aggregate
STANDARD TEST METHOD FOR UNIT WEIGHT AND VOIDS IN AGGREGATE (AASHTO NO. T 19/T19M)
STANDARD TEST METHOD FOR UNIT WEIGHT AND VOIDS IN AGGREGATE

: In stock

: ASTM

:

:

Format
$45.00

Publication Date: 02/01/2016 - Complete Document

Description :

This test method covers the determination of bulk density (“unit weight”) of aggregate in a compacted or loose condition, and calculated voids between particles in fine, coarse, or mixed aggregates based on the same determination. This test method is applicable to aggregates not exceeding 125 mm [5 in.] in nominal maximum size.

NOTE 1—Unit weight is the traditional terminology used to describe the property determined by this test method, which is weight per unit volume (more correctly, mass per unit volume or density).

The values stated in either SI units or inch-pound units are to be regarded separately as standard, as appropriate for a specification with which this test method is used. An exception is with regard to sieve sizes and nominal size of aggregate, in which the SI values are the standard as stated in Specification E11. Within the text, inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

*A Summary of Changes section appears at the end of this standard

 

Document Type : Complete Document

Language : English

Page Count : 5

Publication Date : 02/01/2016

Revision : 16

Status : Current

Title : Standard Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate

Publication Date: 12/01/2009 - Complete Document

Description :

This test method covers the determination of bulk density ("unit weight") of aggregate in a compacted or loose condition, and calculated voids between particles in fine, coarse, or mixed aggregates based on the same determination. This test method is applicable to aggregates not exceeding 125 mm [5 in.] in nominal maximum size.

NOTE 1—Unit weight is the traditional terminology used to describe the property determined by this test method, which is weight per unit volume (more correctly, mass per unit volume or density).

The values stated in either SI units or inch-pound units are to be regarded separately as standard, as appropriate for a specification with which this test method is used. An exception is with regard to sieve sizes and nominal size of aggregate, in which the SI values are the standard as stated in Specification E11. Within the text, inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

*A Summary of Changes section appears at the end of this standard.

Document Type : Complete Document

Language : English

Page Count : 5

Publication Date : 12/01/2009

Revision : 09

Status : Historical

Title : Standard Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate

Publication Date: 08/01/2007 - Complete Document

Description :

This test method covers the determination of bulk density ("unit weight") of aggregate in a compacted or loose condition, and calculated voids between particles in fine, coarse, or mixed aggregates based on the same determination. This test method is applicable to aggregates not exceeding 125 mm [5 in.] in nominal maximum size.

NOTE 1—Unit weight is the traditional terminology used to describe the property determined by this test method, which is weight per unit volume (more correctly, mass per unit volume or density).

The values stated in either SI units or inch-pound units are to be regarded separately as standard, as appropriate for a specification with which this test method is used. An exception is with regard to sieve sizes and nominal size of aggregate, in which the SI values are the standard as stated in Specification E 11. Within the text, inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore each system must be used independently of the other, without combining values in any way.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

*A Summary of Changes section appears at the end of this standard.

Document Type : Complete Document

Language : English

Page Count : 5

Publication Date : 08/01/2007

Revision : 07

Status : Historical

Title : Standard Test Method for Bulk Density ("Unit Weight") and Voids in Aggregate

Publication Date: 07/10/1997 - Complete Document Changes Incorporated *

Description :

This test method covers the determination of bulk density ("unit weight") of aggregate in a compacted or loose condition, and calculated voids between particles in fine, coarse, or mixed aggregates based on the same determination. This test method is applicable to aggregates not exceeding 5 in. [125 mm] in nominal maximum size.

NOTE 1 - Unit weight is the traditional terminology used to describe the property determined by this test method, which is weight per unit volume (more correctly, mass per unit volume or density).

The values stated in either inch-pound units or SI units are to be regarded separately as standard, as appropriate for a specification with which this test method is used. An exception is with regard to sieve sizes and nominal size of aggregate, in which the SI values are the standard as stated in Specification E 11. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore each system must be used independently of the other, without combining values in any way.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Document Type : Complete Document

Edition : AASHTO No.: T 19/T19M

Language : English

Page Count : 4

Publication Date : 07/10/1997

Revision : 97

Status : Historical

Supplement : W/

Title : Standard Test Method for Bulk Density ("Unit Weight") and Voids in Aggregate

Publication Date: 07/10/1997 - Complete Document *

Description :

1. Scope

1.1 This test method covers the determination of bulk density ("unit weight") of aggregate in a compacted or loose condition, and calculated voids between particles in fine, coarse, or mixed aggregates based on the same determination. This test method is applicable to aggregates not exceeding 5 in. [125 mm] in nominal maximum size.

NOTE 1--Unit weight is the traditional terminology used to describe the property determined by this test method, which is weight per unit volume (more correctly, mass per unit volume or density).

1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard, as appropriate for a specification with which this test method is used. An exception is with regard to sieve sizes and nominal size of aggregate, in which the SI values are the standard as stated in Specification E 11. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore each system must be used independently of the other, without combining values in any way.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Document Type : Complete Document

Edition : AASHTO No.: T 19/T19M

Language : English

Page Count : 4

Publication Date : 07/10/1997

Revision : 97

Status : Historical

Title : Standard Test Method for Bulk Density ("Unit Weight") and Voids in Aggregate

Publication Date: 01/01/1991 - Complete Document *

Document Type : Complete Document

Edition : AASHTO T19

Language : English

Page Count : 4

Publication Date : 01/01/1991

Revision : 91A

Status : Historical

Title : Standard Test Method for Unit Weight and Voids in Aggregate

Publication Date: 10/15/1991 - Complete Document

Document Type : Complete Document

Language : English

Page Count : 4

Publication Date : 10/15/1991

Revision : 91

Status : Historical

Title : STANDARD TEST METHOD FOR UNIT WEIGHT AND VOIDS IN AGGREGATE (AASHTO NO. T 19/T19M)

Publication Date: 01/01/1990 - Complete Document

Document Type : Complete Document

Language : English

Page Count : 4

Publication Date : 01/01/1990

Revision : 90

Status : Historical

Title : STANDARD TEST METHOD FOR UNIT WEIGHT AND VOIDS IN AGGREGATE

See More titles in ASTM

See More titles in ASTM A-R

See More titles in ASTM C